Advance Series 1 Lifts
- Designed primarily for industrial applications such as lumber plants, plywood plants, mill shops, machine shops and any other industry or occupation that could use hydraulic scissor lifts either for loading or unloading applications.
- Units come complete with hand or foot controls as standard and are ready to be plugged in, in order that they can go to work to assist the operators.
- All units come completely prewired, including controls as specified by the customers and merely have a three phase power connection made into terminals in the control box in order that they can go to work.
- Models operate in the “up” direction by depressing the “up” control button which starts the pump unit. Level and position is maintained against a check valve built into the pump unit, therefore, any desired height can be achieved and maintained.
- All models are lowered by means of energizing a hydraulic solenoid operated down valve. The pumping unit does not operate when the lift is travelling in the down direction.
- Grease fittings are included at critical wear points. Points not readily accessible are fitted with sealed bearings.
- Loads may be positioned at any point in the “up” and “down” travel making the loads fully accessible to the operator from all sides and levels. This in turn eliminates worker fatigue and promotes safer handling of your product.
Advance Series 2 Lifts
- Designed for use as portable lifts, truck mounted lifts or as permanently installed inter-floor type of lift.
- Can be supplied in basic standard form or can be fully equipped complete with wheels for manual propulsion or equipped with power wheels or permanently installed in pits facilitating a floor flush loading and unloading condition. When installed in this manner these units can be equipped with electric inter-locked gates, safety enclosures, automatic controls, hand rails, hinge plates and a host of other accessories to suit your particular requirements
- Deck design allows for the unit to be supplied as a flat top or with hand rails located on deck surface to suit your material flow straight through or on and off at right angles to each other.
- Self-contained hydraulic pump system provides fail-safe protection during power failures.
- All hydraulic scissor lifts are supplied with fully adjustable electric or hydraulic limit switches to protect the lift cylinder mechanism and hydraulic pump system.
- In the event of the hydraulic lift being used for automatic accumulation or unloading operations, we can supply automatic or semi-automatic controls to suit your requirements. Please advise your needs and we will furnish the necessary information.
- These versatile lifts can be used to feed or to accumulate material from machines, conveyor lines or any location where a lifting or accumulating problem occurs.
- Use these hydraulic lifts to increase production, reduce operator fatigue and eliminate material handling hazards.
- Scissor lifts can be supplied with the following voltages (please specifiy when ordering): 110 volt single phase; 220 volt single phase; 208/220/440/550/600 volt three phase.
- All hydraulic lifts come complete with top and base frames manufactured from angle or channel construction, depending on model selected.
Various Pump Units Available
- Air motor complete with air operated foot control (used for hazardous locations ) – no electrical power required.
- DC battery operated pumps can be supplied to meet your requirements.
- Hand or foot operated pumps (please note these are extremely slow and fatiguing to operate).
- Continuous running pump units used where rapid cycling and continuous operation is necessary.
Wheels
- Standard castering and non-castering wheels can be supplied to suit your needs.
- V-grooved steel wheels complete with inverted angle tracks can be supplied for straight ahead easy movement of heavy loads.
- Power drive wheels can be supplied to suit your needs.
- Fixed casters on lift complete with tow-bar dolly handle can be supplied to facilitate mobility of lift from position to position and by slipping tow-bar out from toe tongue unit can be rendered stationary at any location to suit your needs.
- Units can be supplied complete with four swivel casters for total maneuverability.
Safety Features – Optional for Extra Cost
- Lift will not lower in the event of hose rupture (locked by velocity fuse).
- Lift will not lower during a power failure (locked by normally closed solenoid). Please not this is a standard item.
- Lift deck can be supplied with anti-skid surfacing (standard on truck lifts).
- Lifts down movement wills top when sensing bar contacts any object (electric perimeter bar).
- Mechanical service blocks to lock lift in elevated position for service work.
- Handrails can be supplied to suit your requirements.
- Hinge plates can be supplied to suit your requirements.
- Four only hold down angles with 1″ holes can be supplied to suit your requirements.
All pivot and wear points are equipped with specially hardened pins or bearings to minimize maintenance.
Hydraulic cylinder cross heads are equipped with oilite bronze bushings.